Triconex 9662-810 Panel Field Termination Option, 4.5 in (11.43 cm) Width (across DIN rail), 5 in (12.7 cm) Length (along DIN rail) and 4.25 in (10.795 cm) Height (out from DIN rail)  --Automatic on-load voltage regulation for single transformers --Automatic on-load voltage regulation for 4 to 8 transformers in parallel operation, based on the minimum loop current principle or the master-slave follower pinciple  --Control of up to 30 switchgears --Interlocking modules for different wiring methods, ready to use --Various reservation processing functions --Synchronization, simultaneous detection and voltage detection --Dual-position universal switch --32-position selector switch

Analog Input Modules Analog Input (AI) Modules includes three independent input channels. Each input channel receives variable voltage signals from each point, converts them to digital values, and transmits the values to the three Main Processor modules on demand. In TMR mode, one value is then selected using a midvalue selection algorithm to ensure correct data for every scan. Sensing of each input point is performed in a manner that prevents a single failure on one channel. Analog Input Modules require a separate external termination panel (ETP) with a cable interface to the Tricon backplane. Each module is mechanically keyed for proper installation in a Tricon chassis. affecting another channel. Each Analog Input Module sustains complete, ongoing diagnostics for each channel. Failure of any diagnostic on any channel activates the Fault indicator for the module, which in turn activates the chassis alarm signal. The module’s Fault indicator merely reports a channelfault, not a module failure—the module can operate properly with as many as two faulty channels.

Analog Input Modules Analog Input (AI) Modules includes three independent input channels. Each input channel receives variable voltage signals from each point, converts them to digital values, and transmits the values to the three Main Processor modules on demand. In TMR mode, one value is then selected using a midvalue selection algorithm to ensure correct data for every scan. Sensing of each input point is performed in a manner that prevents a single failure on one channel. Analog Input Modules require a separate external termination panel (ETP) with a cable interface to the Tricon backplane. Each module is mechanically keyed for proper installation in a Tricon chassis. affecting another channel. Each Analog Input Module sustains complete, ongoing diagnostics for each channel. Failure of any diagnostic on any channel activates the Fault indicator for the module, which in turn activates the chassis alarm signal. The module’s Fault indicator merely reports a channelfault, not a module failure—the module can operate properly with as many as two faulty channels.

LV525342 circuit breaker EasyPact CVS250F, 36 kA at 415 VAC, 200 A rating thermal magnetic TM-D trip unit, 4P 3d EasyPact CVS250F is a 4 poles 3d fixed circuit breaker with a high level of performance and cost-saving functionality. It is an optimal choice for small and medium-sized buildings protection applications. The breaking capacity (Icu) is 36kA rms at 415VAC 50/60Hz. The operational voltage is 440VAC 50/60Hz. This product embeds a 200A rating thermal-magnetic trip unit (TMD). TMD trip unit provides an adjustable thermal overload protection and a fixed magnetic protection. This 4 poles version (140mm x 161mm x 86mm) comes with a variety of optional functions and accessories. EasyPact CVS250F is compliant with international standards (IEC 60947, CCC, EAC). It can be installed in class II insulation switchboards as it is a class II front face device (IEC 60664-1).

This extended I/O card enables your drive to meet the needs of more complex or extensive applications. It comprises four logic inputs, two analog inputs, one input for PTC probe and one frequency control input. It also comprises three logic outputs and two analog outputs. It is compatible with Altivar 61 and Altivar 71.

Schneider VZ3TM2200M4371 Motors, Actuators, Solenoids and Drivers Accessories

Control Mode Open-loop vector or V/Hz induction motor control Open-loop Rotor Flux Control for induction motors (RFC-A) Open-loop permanent magnet motor control (RFC-S) Closed-loop Rotor Flux Control for induction motors (RFC-A) Closed-loop permanent magnet motor control (RFC-S) Active Front End (AFE) power quality convertor

Allen-Bradley 80026-524-01-R Power Supply, In: 100-240VAC, Out: 56VDC 26.8A 1500W

Bosch Rexroth AB32-12/01-K-054-22 Heat exchanger Condition :Brand New Warranty :12 months 

Main Range of Product Modicon Quantum automation platform Product or Component Type Rack backplane Product Specific Application For distributed I/O modules For remote I/O modules For local I/O modules Complementary Free slots 6 Mounting Support Mounting plate Fixing Mode By screw Net Weight 1.41 lb(US) (0.64 kg) Ordering and shipping details Category US1PC2118155 Discount Schedule PC21 GTIN 3595861127357 Returnability Yes Country of origin FR Packing Units Unit Type of Package 1 PCE Number of Units in Package 1 1 Package 1 Height 1.81 in (4.6 cm) Package 1 Width 11.65 in (29.6 cm) Package 1 Length 14.88 in (37.8 cm) Package 1 Weight 2.80 lb(US) (1.27 kg)

Introduce for Triconex Tricon's control system: The main features of Tricon's control system Tricon is a programmable and process control technology with high fault tolerance. Its characteristics are as follows: A. Triple modular redundancy structure (TMR) is provided, with three identical sub-circuits each performing an independent degree of control. There is also a dedicated hardware/software architecture for "voting" on input and output. Ability to tolerate harsh industrial environment. C. It can be installed on site and can be installed and repaired at the module level online on site without disturbing the field wiring. D. Supports up to 118 I/O modules (analog and digital) and optional communication modules. Communication modules can Connect to Modbus hosts and dependents, or to Foxboro and Honeywell Distributed Control System (DCS), other Tricons in a peer-to-peer network, and external hosts on a TCP/IP network. E. Can support remote I/O modules located up to 12 km away from the mainframe. F. Develop and debug the control program by using the programming software based on Windows NT system. G. Intelligent functions in input and output modules to reduce workload on the main processor. Each I/O module has three microprocessors. The input module's microprocessor filters and repairs the input and diagnoses hardware failures on the module. The output module microprocessor provides information for the voting of the output data, checks the validity of the output state through the feedback loop voltage at the output end, and can diagnose the field line problems. H. Provide comprehensive online diagnosis with repair capability. I. Routine maintenance can be performed while Tricon is up and running without interrupting the control process. J. Provide "hot standby" support for I/O modules, which can be used in certain critical situations where services cannot be provided in a timely manner.

Triconex 9761-210 Panel Field Termination Option, 4.5 in (11.43 cm) Width (across DIN rail), 5 in (12.7 cm) Length (along DIN rail) and 4.25 in (10.795 cm) Height (out from DIN rail) Simple Type: Termination Panel

Contact Eugene --Sales Manager E-mail:eugene@kerienplc.com Tel.& WeChat:86-13606038172 QQ:1906683268 Add: 1803 B-Building Taidi Haicang, Xiamen, China Product Packing · Original package or international import package. Shipping and delivery · Items will be shipped within 3 business days from payment confirmation via UPS DHL FEDEX TNT or EMS etc · We can always deliver in prompt Payment Terms · Buyer Pays the shipping Charge and handling worldwide. · We accept TT.   ABOUT US  Kerien Automation Co., Ltd. is located in the beautiful coastal city - Xiamen. It is a high-tech enterprise specializing in large-scale system spare parts (distributed control system, programmable controller, redundant fault-tolerant control system, robot control system, large servo control system) and other imported automation system spare parts, module sales and system integration. The automation brand products have a strong advantage, the company is equipped with professional technical personnel, aiming to provide customers with better service. Dade Huicheng Technology (Xiamen) Co., Ltd. which is in the spirit of professionalism, integrity, and cooperation,  dedicated to provide customers with better service, better price. Welcome to inquire.   Advantage Products 1.25x1.25 Valenite VDBS-20 Econ-o-Groove Tool Holder  1.25 x 1.5 x 5.5 Manchester Tool Holder 206-144 1.25 x 1.5 x 5.5 Manchester Tool Holder 206-144 1.25 x 1.25 x6 Valenite Tool Holder NVCTGR-20-4 CTGPR 1.25 x 1.25 x5 Kennametal Tool Holder NA8 DCLNL-204D 1.25 x 1.25 x 6 Kennametal Tool Holder KTGPL-204D 1.25 x 1.25 x 6 Kennametal Tool Holder CTCPL-204D 1.25 x 1.25 x 6 Kennametal Tool Holder CTCPL-204D 1.25 x 1.25 x 5.75 Valenite Tool Holder SD-TMR-20-66 1.25 x 1.25 x 5.75 Valenite Tool Holder SD-TMR-20-66 1.25 x 1.25 x 5.75 Valenite Tool Holder SD-TMR-20-4D 1.25 x 1.25 x 5.75 Valenite Tool Holder SD-TMR-20-4D 1.25 x 1.25 x 5.75 Valenite Tool Holder SD-TML-20-4D 1.25 x 1.25 x 5 Valenite Tool Holder SD-TMR-20 1.25 x 1.25 x 5 Valenite Tool Holder SD-TMR-20 1.25 x 1.25 x 5 Kennametal Tool Holder DTGNL-205C 1.25 x 1.25 x 5 Kennametal Tool Holder DTGNL-205C 1.25 x 1.25 x 5 Kennametal Tool Holder DDJNL-205C 1.25 x 1.25 x 5 Kennametal Tool Holder CTCPL-204D 1.25 x 1.25 x 5 Kennametal Tool Holder CTCPL-204D 1.25 Carboloy Carbide Insert Lathe Boring Bar BBA 5 1.1 KVA Fanuc Transformer A80L 0001 0176 03 A80L0001 1.1 KVA Fanuc Pertronics Transformer A80L 0001 0176 02 1.1 KVA Fanuc CNC TRANSFORMER A80L-0001-0317-02  1 x 1 x 6 Valenite Tool Holder HPTGL-16-4D HPTGL164D 1 x 1 x 5.75 Valenite Tool Holder SD-TML-16-3D 1 Valenite CAT 50 Taper CAT50 End Mill Holder EMH 1 Ton P  H Zip-Lift Hoist Crane 2000 Lb Pound Capacity Electric Chain Air Hois 1 MT to 4 MT Morse Taper Adapter 1MT to 4MT 1 MT to 4 MT Morse Taper Adapter 1MT to 4MT 1 MT to 4 MT Morse Taper Adapter 1MT to 4MT 1 HP TEEC Trochoid Pump TK-150 3 Phase 220/380 V 1 Command CAT 50 Taper CAT50 End Mill Holder EMH 1 1/4 Valenite CAT 50 Taper CAT50 End Mill Holder EMH Our service 1)100% New - Original Factory Seal  2)Warranty: 12 months 3)Package: Original packing with cartons 4)Delivery time: Shipped in 3 days after payment

Siemens 6FC5303-0AF50-3BA1 Maschinensteuertafel MCP 429C-M IE ERGOLINE Version: D , SN:T-E76084904

TCSEAAF1LFS00 | Schneider Electric | Fiber optic adaptor for TCSESM switches